[ Pobierz całość w formacie PDF ]

M-Drive and activated via the M-Drive Manager.
The Head-Up Display in the M-view can show
the following information:
" All Warnings
" Engine Speed with shift lights in the
speed indicator (not the absolute value)
" Road Speed
" Engaged Gear.
1
1
2
3
5 4
3 2
M-View Default View
Index Explanation Index Explanation
1 Current Engine Speed Highlighted 1 Navigation Instructions
2 Advance Warning Field 2 Cruise Control Status
3 Red Warning Field 3 Speed
4 Speed
5 Gear Display
Note: The visibility of the displays in the Head-Up Display is influenced by:
" Sunglasses with certain polarization filters
" Certain seating positions
" Objects on the cover of the Head-Up Display
" Wet road surface and unfavorable lighting conditions
10
E60 M5 Driver Information Systems
Enabling M-View
To select M-View you have to utilize the display settings Menu of the iDrive system.
With the engine running or the ignition switched on:
Press the button to activate or deactivate the Head-Up Display.
1. Press the button.
(This opens the start menu.)
2. Press the controller
(Opens the i-Menu)
3. Select "Display settings"
and press the controller.
4. Select "Head-Up Display"
and press the controller.
5. Select desired information of
Head-Up Display.
6. Press the controller.
When M View is selected,not all information usually selectable for the HUD are not
available. Information unavailable in the M view appears on the Control Display in gray
and cannot be selected.
The settings are stored for the remote key currently in use.
Note: The M view for the Head-Up Display can also be programmed into the
MDrive button on the steering wheel.
Setting Brightness
The brightness of the display is automatically adapted to the ambient lighting conditions.
However, you can change the base setting. With the low beams switched on, the bright-
ness can also be adjusted with the knurled wheel of the instrument lighting.
To adjust brightness:
1. Open the start menu.
2. Press the controller to open the menu.
3. Select "Display settings" and press the controller.
4. Select "Brightness" and press the controller.
5. Move the controller to the left to select "Head-Up Display".
6. Turn the controller until the desired setting is selected.
The setting is stored for the remote control currently in use.
Reset to Default
This option allows all the setting in MDrive to revert to factory or default settings.
11
E60 M5 Driver Information Systems
Oil Level Indicator
The M5 is equipped with an electronic oil level indicator. The display is selected with the
BC control.
The oil level is indicated in the information field of the on-board computer (BC) in the
instrument cluster.
The sensor is the quality and condition sensor (QLT) from the E65. The entire measure-
ment logic is resident in the engine management (MS_S65) control unit.
The long-term value last stored is shown after starting the engine.
Basically there are two different measuring methods:
" Long-term Measurement
" Quick Measurement
Oil Level Indicator
Index Explanation
1 Oil Level
2 Maximum Level Mark
3 Minimum Level Mark
Long-Term Measurement
The engine management permanently measures the oil level and derives the mean
value from the measurement results which is then shown in the on-board computer.
The ECU requires an engine operating time of approx. 10 minutes to establish a
long-term value.
Note: The average speed information was removed from the BC menu to
accommodate the oil level indication in the on-board computer.
12
E60 M5 Driver Information Systems
Quick Measurement
The quick measurement method provides the option of measuring the oil level with only
a short time delay (e.g. topping up oil, oil service).
The quick measurement must be initiated manually by pressing and holding the BC but-
ton (approx. 2 seconds) in the oil level indication setting.
The displayed value indicates the quantity of oil above the minimum level. The value
should be between MIN 0.0 l and MAX 1.0 l.
Display: 1.5 l means overfilled, the bar indicator is additionally filled above Maximum.
Perform Quick Measurement
" Park vehicle in horizontal position
" Engine running at idle speed
" Oil temperature above 70°C
" Select engine oil level indicator in on-board computer
" Press and hold BC button > 2 s.
The oil level display changes and shows only two dashes (see below) and a clock symbol.
The clock symbol indicates that the oil level is being measured. The clock symbol would
disappear if the engine speed is now increased. The measurement is continued as soon
as the measurement criteria are met again.
The pure measuring time is approximately 60 s. The long-term value last stored is delet-
ed with initiation of the quick measurement.
Index Explanation
1 0.6 Liter Minimum
2 Minimum Level
3 Overfilled (bar full and 1.5 Liter displayed)
4 Maximum Level
5 Oil Level Measurement Running
6 No Measured Value Stores and Measurement Criteria not Met
13
E60 M5 Driver Information Systems [ Pobierz całość w formacie PDF ]